Bookmark this page for future reference!
Flame Effect Definition
Flame Effect is defined as “The combustion of solids, liquids, or gases to produce thermal, physical, visual, or audible phenomena before an audience.” This includes all flames that are automated, switched, pressurized or having any other action than simply being lit on fire; as well as projects using propane or other liquid or gaseous fuels.
Fire Art Safety Team (FAST)
Burning Man has developed a Fire Art Safety Team (FAST) whose mission is to provide experienced support for fire artists and to ensure the safe use of fire at the Burning Man Event. FAST comprises artists, fire safety personnel and industry professionals who will Assist artists in the safe execution of Open Fire, Flame Effects, and/or Pyrotechnics in installations, theme camps and mutant vehicles. FAST will inspect artworks incorporating fire and issue the appropriate Burn License(s) once the artwork has been approved.
A FAST Artist Liaison will work with the Artist and Fire Safety Liaison during the pre-Event evaluation process. Take advantage of FAST’s experience in planning your artwork.
Fire Art & Event Stipulations
Burning Man’s agreements with the U.S. Bureau of Land Management are in the form of Event Stipulations, which state that for public safety reasons, artworks utilizing Open Fire, Flame Effects and/or Pyrotechnics require safety inspection and approval in the form of a Burn License (laminate).
FAST and outside authorities, including law enforcement, retain jurisdiction over all flame classifications. They have the right to request to see the Burn License and if not presented can override, stop, alter or cancel any artwork or performance with just cause. They have access to all areas of the artwork or performance at all times.
Safety Responsibility For Flame Effect Art
All artists and their crews are responsible for their own art. Because of the dangerous nature of Flame Effects, no one may operate a Flame Effect without the approval of FAST.
It is the responsibility of the Artist to secure FAST approval for their Flame Effect installation, initially based on submitted documentation, and ultimately based on a physical inspection of the construction and operating characteristics of the installation. Evidence of approval to operate a Flame Effect is in the form of a Burn License (laminate) issued and signed by a member of FAST.
Except for testing under the supervision of a member of FAST, no one may operate a Flame Effect within Black Rock City without physically possessing the license issued specifically for that Flame Effect.
Fire Art Approval Process
The approval process for your fire art project involves a number of steps, starting well before you depart for Black Rock City, and culminating at the Event. This multiple-step approval process is not meant to bog Artists down, but rather to ensure that all safety requirements are adhered to.
- Designate qualified persons to fill the following Project Team roles (defined below): Fire Safety Liaison and Leave No Trace Lead.
- Complete and submit the Art Installation questionnaire, including:
- Fire Safety Liaison name and contact information
- Flame Effect Scenario
- Required Diagrams
- Safety and Emergency Plans
- Leave No Trace Plan
- FAST reviews your submitted documentation.
- Your Project Team, through the Fire Safety Liaison, engages in an ongoing dialogue with a FAST Artist Liaison to ensure that your plans are complete and in conformity with FAST guidelines.
- Your Fire Safety Liaison maintains email contact with FAST to ensure that all parties are notified of updates and changes.
- Prepare your Mutant Vehicle and its Flame Effects for inspection.
- Bring the vehicle to the DMV for inspection of all systems, including its Flame Effects. The Fire Safety Liaison and Flame Effects Operator must be present at this inspection. At least two FAST inspectors are on duty at the DMV inspection station during inspection hours. After the Flame Effects pass inspection a Flame Effects License (laminate) will be issued.
Project Team Roles
Artist must designate knowledgeable and capable individuals to fill the key roles listed below. Together, the individuals filling these roles, plus the artist him/herself, make up your Flame Effect Project Team.
It is the joint responsibility of the Artist and the Fire Safety Liaison to disseminate information and applicable deadlines to all Project Team members. The Artist registering the artwork and the Fire Safety Liaison can be the same person or two different people.
Each of the following roles is important and will require the full attention of the person chosen to fill it.
Fire Safety Liaison
The Fire Safety Liaison serves as the primary point of contact for all communication between your project and FAST, and is responsible for ensuring that the artwork’s use of fire conforms to all applicable guidelines. This responsibility includes:
- Ensuring that all items of required documentation are complete and accurate.
- Receiving feedback and addressing questions and safety concerns raised by the FAST Artist Liaison assigned to evaluate the project’s documentation.
- Promptly providing documentation updates to FAST, whether in response to FAST feedback or to design changes independently undertaken by the project.
- Ensuring that the artwork is constructed and operated in accordance with the plan approved by FAST, and that the artwork will not be operated while any identifiable safety hazards are present.
Leave No Trace Lead
The Leave No Trace (LNT) Lead is responsible for organizing periodic clean-up around the vehicle as needed, and post-event clean-up after the vehicle is dismantled. The person selected to be LNT Lead should be adept at recruiting and organizing others to participate in clean-up efforts. Specific responsibilities include:
- Recruiting and organizing LNT crew and ensuring there are enough people for the task.
- Securing proper clean-up tools, including trash cans.
- Leading crew in both daily and post-event clean-up efforts.
The post-event clean-up includes pickup and removal of any materials left on the playa after dismantling the vehicle, including any fuel or chemical residue, loose parts, pyrotechnic debris and any other MOOP (Matter Out Of Place) on site. All MOOP removed must be packed out of Black Rock City.
Fire Art Safety Plan – Required Documentation
The following items of documentation must be submitted for review and approval by FAST.
Flame Effects Scenario
Your Flame Effects Scenario is a complete, detailed description of how your artwork incorporates and uses fire. It should include details such as:
- How your device operates
- The fuel(s) it uses, how its fuel is stored, and how fuel flow is controlled
- The types and rated capacities of the components it incorporates, including hoses, valves, solenoids, regulators (and the pressures you intend to set them to), pressure vessels, pumps, pressurization systems, fans/blowers, the pilot light or ignition system, and any other details you may have.
When writing your Flame Effects Scenario, please be as clear and concise as possible, while also being as detailed and technical as necessary, to fully convey how your fire elements will work and what will go into making them work that way. If you have not completed the design or construction of your artwork, just be as accurate and complete as you can. If we need further details or clarifications we will contact you.
Flame Effect Diagrams
You will be required to submit detailed diagrams or schematics showing all plumbing and electrical arrangements and controls, and any other relevant technical details. These diagrams should at a minimum illustrate the flow of fuels from the supply to the effect head(s), and all the components those fuels pass through along the way. In particular, you must indicate the locations of any shut-off or other control valves, regulators, pressure vessels, pumps, pressurization systems, fans/blowers, ignition systems and anything else that affects the flow or burning of your Flame Effect’s fuels.
If you have not completed the design or construction of your artwork, just be as accurate and complete as you can. If we need further details or clarifications we will contact you.
Note: You will need to provide a final set of complete drawings by the last full work week in July.
The following Layout Diagrams are required:
- Vehicle Flame Effect Layout
- Fuel Location & Protection: Location of fuel tanks and lines and how they are protected from damage by collision or participant actions.
- Safety Zones: Locations of flame heads relative to where participants are able to stand.
- Fire Extinguishers: Types and locations.
- First Aid Kit: Location of first aid kit with burn supplies.
- Base Camp Layout
- Storage location(s) for flammable liquids, fuel gases or other hazardous/flammable materials.
- Storage location(s) for empty fuel containers, if different from above.
- Safety perimeters and barriers, and distances to public areas and habitations.
- 20′ wide fire lane from street to storage location(s) listed above.
- Fire extinguisher locations.
Your Safety Plan should describe all the measures that your crew will employ to ensure that your installation will be safe for participants, performers and crew, both during and after construction, and during strike and clean-up. At a minimum, it should cover:
- Illumination and protection from vehicle traffic for all elements of the installation, including the artwork itself, fuel supplies and fuel storage, operating positions, generators, etc.
- Types, sizes and placement of fire extinguishers or other fire suppression means that will be kept on hand
- Location and contents of first aid kit(s)
- List of Material Safety Data Sheets to be kept on hand
- Safety training your crew members have
- Safety-specific crew roles and responsibilities
- Safety procedures and protocols:
- Fueling procedures: how do you ensure that fueling is done safely?
- Daily safety check: what conditions do you check for?
- Operating procedures: what conditions do you watch for while operating?
- Safety features, if any, built in to the installation
- Safety perimeters, and how they are enforced
Emergency Response Plan
No matter how comprehensive your Safety Plan, things still go wrong. Your Emergency Response Plan should list all the ways things may go wrong and expose your crew or other participants to potential injury, and how your crew will respond when they do. At a minimum it should cover:
- Emergency shut-off/shut-down procedures
- Response to fuel leaks
- Response to liquid fuel spills, small and large
- Response to unplanned fires, small and large
- Response to damage (or incipient damage) caused by wind, vehicle collision or other physical forces
- Response to hazardous material exposure of crew, performer or participant
- Response to injury sustained by crew, performer or participant
Leave No Trace Plan
The Artist, Leave No Trace Lead and crew are responsible for all clean up at the art installation site, both nightly and when the Burning Man event ends. Your Leave No Trace plan describes how you will accomplish this. At a minimum it should cover:
- Nightly clean-up procedure
- End-of-event clean-up procedure
- Emergency clean-up procedures (e.g., for liquid fuel spills)
- Clean-up tools and materials to be used
Safety Guidelines for Flame Effects
Please read carefully!
Failure to do so may result in your project not being permitted at Burning Man.
The majority of Flame Effects at Burning Man are Liquefied Petroleum Gas (LP-Gas) effects; LP-Gas is often commonly referred to as propane. Most of the guidelines below deal with LP-Gas as a fuel. Regardless of fuel type or technological basis, all Flame Effects must be constructed in such a way as to meet or exceed applicable laws, codes and industry standards.
The National Fire Prevention Association (NFPA) publishes numerous codes and standards for the construction and use of LP-Gas systems, including:
- NFPA 54 – National Fuel Gas Code
- NFPA 58 – Liquefied Petroleum Gas Code
- NFPA 160 – Standard for the Use of Flame Effects Before an Audience
NFPA documents are available for viewing and purchase on the NFPA website and should be reviewed by all Flame Effects artists.
Construction of Flame Effects
- All LP-Gas cylinders shall be designed, fabricated, tested, and marked in accordance with the regulations of the US Department of Transportation (DOT) or the ASME Boiler and Pressure Vessel Code.
- All LP-Gas cylinders must have an unexpired certification date stamp and be in good working order. Tanks in poor condition or out of date are a danger to fill and may cause injury to the fuel team, the artists, and/or participants.
- Each LP-Gas Flame Effect must have a single 1/4-turn shut-off valve as the primary emergency fuel shut-off. When closed, this valve must inhibit all fuel flow to the Flame Effect, regardless of how many LP-Gas cylinders are connected to the Flame Effect. This valve must be exposed and visible at all times, and must be clearly marked as the emergency fuel shut-off.
- All components of the fuel system (fittings, piping, valves, connectors, etc.) must be designed and rated for both the type and pressure of fuel being used. The use of improper fittings can lead to leaks and failures in the fuel system resulting in fires and or injury.
- All LP-Gas metallic piping and fittings that will operate at a pressure greater than 125 psi shall be schedule 80 or heavier.
- All LP-Gas Hoses that will be operated in excess of 5 psi shall be designed for a working pressure of at least 350 psi and shall be continuously marked by the manufacturer to indicate its maximum operating pressure and compatibility with LP-Gas.
- Air or pneumatic line is not acceptable as fuel hose. LP-Gas degrades rubber hose not specifically designed for use with that fuel. This results in the hose cracking from the inside out, potentially leading to a catastrophic failure.
- Hose clamps are prohibited on LP-Gas hose at any pressure. All fuel hose connections shall be factory made, or constructed with a crimped fitting specifically designed for that purpose. Hose clamps are well known for cutting and chafing fuel lines or coming loose, possibly leading to catastrophic failure.
- All metallic tubing joints shall use flare fittings. The use of compression fittings or lead soldered fittings are prohibited.
- Accumulators, surge tanks and other pressure vessels in the system shall be designed, manufactured, and tested in accordance with the ASME Boiler Pressure Vessel Code or the Department of Transportation (DOT) for the pressure of the gas in use.
- Any welding alteration of pressure vessels, or alteration or fabrication of other system components that hold pressure, must be performed by an American Society of Mechanical Engineers (ASME) certified welder, and must be stamped and certified as such.
- If the fuel supply pressure exceeds the maximum allowable operating pressure (MAOP) of an accumulator or other pressure vessel, a regulator shall be installed between the fuel supply and the pressure vessel to reduce the pressure below the pressure vessel’s MAOP. A pressure relief valve shall also be installed in the pressure vessel, with a start-to-leak setting at or below the MAOP and a rate of discharge that exceeds the maximum flow rate of the supply container.
- Fuel tanks for stationary Flame Effects must be protected from vehicle traffic and be well illuminated at night.
- Flame Effects should be constructed and sited in such a way that the flame head and/or hot components are at least six inches from the Playa surface, to prevent baking or scarring of the Playa.
- Any artwork, towers or other structures that incorporate Flame Effects should be secured from the wind and encircled with an appropriate safety perimeter to prevent injury to participants.
Special Considerations for Mutant Vehicles
- Absolutely no Pyrotechnics (fireworks) of any kind may be used on a Mutant Vehicle. There are no exceptions to this rule. Law Enforcement is quite strict on this policy and you will be cited and possibly removed from the event if you or anyone in or on your vehicle violates this prohibition.
- The use of wood fires or liquid-fueled flame effects on Mutant Vehicles is prohibited.
- Transporting open acetylene cylinders, and use of acetylene in Flame Effects on mobile art is prohibited.
- Route your hoses inboard and away from hot exhaust pipes or manifolds. You will be moving and you could run into an unlit object on the Playa or another Mutant Vehicle. All fuel lines should be protected from potential damage due to a collision.
- It is possible that you may have participants on your vehicle. The routing of fuel and electrical lines should also be such that they cannot be damaged by someone grabbing them (say, while traveling over rough terrain) or tripping over them.
- Fuel and electrical lines should be run in such a way as to prevent rubbing, chafing, impingement or other damage that may result from normal use of vehicle.
- Fuel tanks must be mounted and secured within the vehicle so they are protected from damage caused by a collision with another vehicle or solid object, and where participants cannot step or stand on them.
- Fuel tanks should be well ventilated; LP-Gas is heavier than air and in case of a leak will collect in low unventilated areas, resulting in risk of explosion.
- The 1/4-turn main LP-Gas shut-off valve must be placed within easy reach of both the driver and the Flame Effects Operator.
- Flame should be well above the heads of participants: at least 10 feet (3m) above where any participant could stand, whether on the ground, or on your vehicle.
- Flame discharges should be vertical whenever possible; no flame shall be angled closer than 45° to the horizontal.
Maximum LP-Gas Quantity for Mutant Vehicles
In order the ensure the safety of participants and Emergency Services personnel, Burning Man imposes limits on the quantity of LP-Gas that may be carried on Mutant Vehicles. These limits are consistent with regulations imposed by the Nevada Department of Motor Vehicles and the Federal Department of Transportation (DOT), as well as National Fire Protection Association (NFPA) guidelines.
- The total Aggregate Gross Weight (weight of containers plus fuel when all containers are filled to their maximum permitted filling levels) shall not exceed 1000 lb.
- The maximum number of containers shall not exceed ten (10).
- The maximum size DOT cylinder shall be 1000 lb. water capacity (WC).
- The maximum size ASME portable container shall be 200 gallon water capacity (WC).
- ASME containers shall be designed for portable use, and shall have integral appurtenance protection.
- Containers shall be installed on the vehicle to allow adequate ventilation and access to their appurtenances for easy closure in an emergency situation.
- The containers shall be transported on the vehicle upright with the relief valve in communication with the vapor space preventing the venting of liquid LP-Gas.
- Containers shall be secured to prevent movement during transportation.
The formula to obtain the aggregate gross weight of a cylinder is:
AGW = (WC × 0.42) + TW
- AGW = Aggregate Gross Weight
- WC = Water Capacity (marked on cylinder)
- TW = Tare Weight (the weight of the container when empty; marked on cylinder)
Note that Aggregate Gross Weight is only one consideration in sizing your fuel supply. Regardless of the size(s) of the cylinders you choose, you are limited to a total of ten (10) cylinders maximum.
Below are some examples of LP-Gas cylinder combinations that meet the requirements:
- Ten 20# cylinders (380 lb.)
- Ten 30# cylinders (550 lb.)
- Ten 40# cylinders (720 lb.)
- Five 100# cylinders (855 lb.)
- Five 100# cylinders and three 20# cylinders (969 lb.)
Operation of Flame Effects
Flame Effect Operators
Flame Effects operators and assistants must be 21 years of age or older and be trained in the use of fire extinguishers.
Operators and assistants must wear fire resistant clothing while operating Flame Effects.
No carelessness, negligence, or unsafe conditions with Flame Effects shall be tolerated. Do not drink, take drugs, or smoke when working with Flame Effects.
An appropriate audience safety perimeter (and performer’s safety zone if applicable) shall be established well in advance of Flame Effect operation, and must be approved by FAST. Because of the variety of artwork that incorporates Flame Effects, a member of FAST will help you determine the correct perimeter distance.
In any case, a 20′ zone around the Flame Effect must be kept free of all combustible or flammable materials, and nothing should overhang this zone.
Only people familiar with the safety considerations and hazards involved are permitted to connect/disconnect LP-Gas tanks, or to do liquid fuel filling. Wearing personal safety gear (glasses, gloves, etc.) during liquid fuel filling is required.
Daily Safety Check
A daily safety check of all Flame Effect components and connections is mandatory before operation begins. Never start operation of a Flame Effect until the daily safety check is completed. If a safety hazard is identified either during the safety check or during operation, the Fire Safety Liaison must delay or halt operation until the hazard is corrected.
Never light a Flame Effect until all performers, safety monitors and participants are in place and ready.
Never operate a Flame Effect in such a way that it poses a danger to people or property.
As an operator of a Mutant Vehicle, you must be aware of your surroundings and playa conditions. There are many tall structures, participants on stilts, flammable costumes and unpredictable winds. Any of these factors could result in serious injury. Simply being aware of these conditions will go a long way in preventing an injury.
When bringing your Mutant Vehicle onto city streets within the camping area, exercise even more care when discharging flame effects, being aware of the limited clearance between your vehicle and participants, structures (including overhanging obstructions) and other vehicles.
When parking your Mutant Vehicle, park in a safe location away from sources of ignition. Shut down Flame Effects, close fuel supply cylinders, purge your lines and lock out your controls if Flame Effects will be unattended while the vehicle is parked.
Attending to Flame Effects
Flame Effects must never be left unattended. The winds in the desert are highly variable, and may create havoc in a poorly monitored installation. Any Flame Effect found running unattended will be shut down. Egregious and/or repeat offenses will result in the confiscation and/or disabling of the Effect.
No Smoking or Open Flame
ABSOLUTELY no smoking or open flame within 10 feet any storage area where flammable liquids or fuel gases are stored. All fuel and flammables must be stored in approved containers which must remain closed except when filling or dispensing, or when connected to a system for use.
Material Safety Data Sheets
MSDS for any hazardous chemicals used in the construction or operation of the Flame Effect must be kept at the installation, so they are available to guide clean-up activities in case of a material spill, and to provide to emergency medical personnel in case of accidental exposure.
Artist and Fire Safety Liaison agree to keep available at the art installation at least one dry chemical fire extinguisher rated 3A:40B:C, for use in case of any accidental fire at the art installation. Note that this is a minimum. You should plan to have on hand as many fire extinguishers as necessary for the size of your installation and the nature of the fire hazards it presents. If you are unsure how many extinguishers you should have, FAST can advise you.
Not all fire extinguishers work for fighting all fires. You and your crew should understand which type of extinguisher is appropriate for each type of fuel present at your installation.
Dry chemical extinguishers are required where fuel is stored, as they provide the best way to put out a fuel fire. They do make messes that must be cleaned up after use. Also, dry chemical extinguishers start to lose charge after a single discharge and must be serviced and refilled.
Water fire extinguishers are useful for putting out fires involving wood, paper, fabric, and performers’ bodies. These extinguishers must never be used on liquid fuel fires, as they will spread the fire. Also water is a good conductor of electricity, so these extinguishers are a poor choice for fires where energized electrical equipment is present.
CO2 (Carbon Dioxide) extinguishers are good responses to problems with fire props and fires involving electricity. They leave no residue and can be used repeatedly until they run out. But they work for small fires only. CO2 extinguishers are also good for putting out fires on people’s clothing, but use care near exposed skin, since the extinguishing agent exits the horn or nozzle at about -70°F/-56°C.
Wet towels must be available for response to accidental fire on a person (e.g., smothering fire on the face of a fire breather) or to extinguish fire props. Wet towels work better than duvetyn because (a) they both deprive a fire of oxygen and remove heat, and (b) they are more pliable and conform better to the contours of an object, making it easier to achieve an airtight seal. Wet towels can dry quickly in the arid playa environment, so be sure also to provide a closed container of water for re-wetting them, such as a cooler chest or a bucket with a lid.
A basic first aid kit should be available and contain at least the following items for burn treatment and fuel exposure:
- Non-petroleum-based burn cream or aloe vera gel
- Several rolls of 100% cotton gauze and some large gauze pads
- A jug of clean water for cooling burns, or flushing liquid fuel from eyes
- Waterless soap for washing liquid fuel from hands
Cool a first- or second-degree burn right away with water, and continue cooling it for at least 15 minutes.
Severe burns, and fuel exposures to eyes, nose or mouth should be treated by Emergency Medical Services. Medical teams are available in Center Camp or in the plazas located at 3:00 and 9:00 in Black Rock City. In case of fuel exposure, be sure to provide a copy of the relevant MSDS to the responding medical personnel.
In case of fire on a person’s body or clothing, remember this rule: Stop, Drop & Roll! Many people have saved their own lives by dropping and rolling when their clothes caught fire.
- STOP – Stop where you are and DO NOT RUN!
- DROP – Drop to the ground; cover your face with your hands to protect your eyes and airway.
- ROLL – Roll to put out the flames.
If you are near someone whose clothing catches fire, be sure to stop him or her from running and make them Stop, Drop & Roll!
Leave No Trace
The Artist, Leave No Trace Lead and crew are responsible for all clean up at the installation site, both nightly and when the Event ends. The area must be as clean as when you found it, and all MOOP you remove must be packed out of Black Rock City. This is what it means to LEAVE NO TRACE.
Think about Playa clean-up while you are creating your artwork, both in terms of the usual trash that accumulates and extraordinary situations such as fuel spills. How will you prevent these things from happening, and how will you respond if they do?
You must have available at the installation all necessary clean-up tools and materials for both kinds of eventuality, such as shovels, rakes (including “magnetic rakes”), garbage cans (metal ones if you will be dealing with hot ashes), and sealable containers for storage and removal of spill-contaminated Playa dirt.
Bookmark this page for future reference!